Add options stats_interval and stats_interval_opts to allow interval based stats
printing. This provides an easy way to collect stats without code changes,
because opt.stats_print may not work (some binaries never exit).
`cbopaque` can now be overriden without overriding `write_cb` in
the first place. (Otherwise there would be no need to have the
`cbopaque` parameter in `malloc_message`.)
If the confirm_conf option is set, when the program starts, each of
the four malloc_conf strings will be printed, and each option will
be printed when being set.
Small is added purely for convenience. Large flushes wasn't tracked before and
can be useful in analysis. Large fill simply reports nmalloc, since there is no
batch fill for large currently.
When config_stats is enabled track the size of bin->slabs_nonfull in
the new nonfull_slabs counter in bin_stats_t. This metric should be
useful for establishing an upper ceiling on the savings possible by
meshing.
Looking at the thread counts in our services, jemalloc's background thread
is useful, but mostly idle. Add a config option to tune down the number of threads.
"always" marks all user mappings as MADV_HUGEPAGE; while "never" marks all
mappings as MADV_NOHUGEPAGE. The default setting "default" does not change any
settings. Note that all the madvise calls are part of the default extent hooks
by design, so that customized extent hooks have complete control over the
mappings including hugepage settings.
When allocating from dirty extents (which we always prefer if available), large
active extents can get split even if the new allocation is much smaller, in
which case the introduced fragmentation causes high long term damage. This new
option controls the threshold to reuse and split an existing active extent. We
avoid using a large extent for much smaller sizes, in order to reduce
fragmentation. In some workload, adding the threshold improves virtual memory
usage by >10x.
This option controls the max size when grow_retained. This is useful when we
have customized extent hooks reserving physical memory (e.g. 1G huge pages).
Without this feature, the default increasing sequence could result in fragmented
and wasted physical memory.
To avoid the high RSS caused by THP + low usage arena (i.e. THP becomes a
significant percentage), added a new "auto" option which will only start using
THP after a base allocator used up the first THP region. Starting from the
second hugepage (in a single arena), "auto" behaves the same as "always",
i.e. madvise hugepage right away.
Support millisecond resolution for decay times. Among other use cases
this makes it possible to specify a short initial dirty-->muzzy decay
phase, followed by a longer muzzy-->clean decay phase.
This resolves#812.
Add the extent_destroy_t extent destruction hook to extent_hooks_t, and
use it during arena destruction. This hook explicitly communicates to
the callee that the extent must be destroyed or tracked for later reuse,
lest it be permanently leaked. Prior to this change, retained extents
could unintentionally be leaked if extent retention was enabled.
This resolves#560.
Control use of munmap(2) via a run-time option rather than a
compile-time option (with the same per platform default). The old
behavior of --disable-munmap can be achieved with
--with-malloc-conf=munmap:false.
This partially resolves#580.
Simplify configuration by removing the --disable-tcache option, but
replace the testing for that configuration with
--with-malloc-conf=tcache:false.
Fix the thread.arena and thread.tcache.flush mallctls to work correctly
if tcache is disabled.
This partially resolves#580.
Rather than using a LIFO queue to track available extent_t structures,
use a red-black tree, and always choose the oldest/lowest available
during reuse.
Split decay-based purging into two phases, the first of which uses lazy
purging to convert dirty pages to "muzzy", and the second of which uses
forced purging, decommit, or unmapping to convert pages to clean or
destroy them altogether. Not all operating systems support lazy
purging, yet the application may provide extent hooks that implement
lazy purging, so care must be taken to dynamically omit the first phase
when necessary.
The mallctl interfaces change as follows:
- opt.decay_time --> opt.{dirty,muzzy}_decay_time
- arena.<i>.decay_time --> arena.<i>.{dirty,muzzy}_decay_time
- arenas.decay_time --> arenas.{dirty,muzzy}_decay_time
- stats.arenas.<i>.pdirty --> stats.arenas.<i>.p{dirty,muzzy}
- stats.arenas.<i>.{npurge,nmadvise,purged} -->
stats.arenas.<i>.{dirty,muzzy}_{npurge,nmadvise,purged}
This resolves#521.
